Steps Necessary To Pass The 300-625 Exam from Training Expert ActualPDF
Valid Way To Pass CCNP Data Center's 300-625 Exam
NEW QUESTION 27
Which two components are Required for successful MDS USB POAP? (Choose two)
- A. script named poap_script.pl
- B. NTFS formatted USB drive
- C. USB drive in port 1
- D. ENTERPRISE_PKG license
- E. system and kickstart images
Answer: D,E
NEW QUESTION 28
Which EtherType is used by the FCoE Initialization Protocol?
- A. 0x8914
- B. 0x8906
- C. 0xfc0e
- D. 0x8913
Answer: A
NEW QUESTION 29
A storage network engineer is upgrading a Cisco MDS Director with dual supervisor modules.
The install command is executed on the standby supervisor module but fails.
Which action would have prevented this failure?
- A. Fabric Controller Service must be stopped before starting the upgrade.
- B. Cisco Fabric Services must be disabled before starting the upgrade.
- C. All FCoE interfaces configured on the MDS must be shut down before starting the upgrade.
- D. The upgrade must be done on the active supervisor module only.
Answer: D
NEW QUESTION 30
After a subordinate switch requests a domain ID from a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated. What is a solution to the issue?
- A. Enable the FICON feature on the affected VSAN.
- B. Configure a static domain on the subordinate switch and reboot the switch.
- C. Configure IVR NAT on the affected VSAN.
- D. Add the received domain ID to the allowed list.
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/93x/san_switching/configuration/guide/b-cisco-nexus-9000-nx-os-san-switching-configuration-guide-933/b_new_N9000-SAN-Switching-Guide_chapter_0100.html
NEW QUESTION 31
Refer to the exhibit.
The san-user must configure FSPF on the VSAN 500, but fails. An operator with network administrative rights must authorize the san-user to perform this work. Which configuration must the operator apply?
- A. MDS-A(config)# role name sangroup
MDS-A(config-role)# rule 2 permit config feature vsan - B. MDS-A(config)# role name sangroup
MDS-A(config-role)# rule 4 permit config feature fspf - C. MDS-A(config)# role name sangroup
MDS-A(config-role)# vsan policy deny
MDS-A(config-role-vsan)# permit vsan 500 - D. MDS-A(config)# role name sangroup
MDS-A(config-role)# no rule 2
Answer: C
Explanation:
Section: Management and Monitoring
NEW QUESTION 32
Which configuration is available only in Cisco DCNM-SAN Advanced mode?
- A. template-based provisioning
- B. VMpath configuration
- C. IVR
- D. zoning
Answer: C
Explanation:
Section: Deployment
Explanation/Reference:
NEW QUESTION 33
Refer to the exhibit.
Refer to the exhibit. Device alias information must be merged for two fabrics. Which setting must match on both fabrics before the merge can be performed successfully?
- A. qos
- B. session
- C. smart-zoning
- D. device-alias mode
Answer: A
NEW QUESTION 34
Refer to the exhibit.
An engineer is configuring Inter-VSAN routing for two Cisco MDS switches. The FSPF cost between the switches is 500, and the Cisco MDS core virtualizes an IVR NAT domain as shown. Which statement about the topology is correct?
- A. The MDS-Core simulates an IVR NAT, and the FSPF cost is 500.
- B. The MDS-Core simulates an IVR NAT, and increases the cost to 600.
- C. The MDS-Core simulates an IVR NAT, and increases the cost to 501.
- D. The MDS-Core simulates an IVR NAT, and decreases the cost to 400.
Answer: C
NEW QUESTION 35
Refer to the exhibit.
A user who is logged in as an operator cannot update the zoneset. What is the cause of this issue?
- A. Hard zoning is enabled.
- B. The fabric is locked by admin on switch-2.
- C. The fabric is locked by admin on another switch.
- D. Merge control is disabled.
- E. The switch has a conflicting domain ID.
Answer: B
Explanation:
Section: MDS Troubleshooting
NEW QUESTION 36
Drag and drop the items from the left onto the correct descriptions on the right. Not all items are used.
Answer:
Explanation:
NEW QUESTION 37
Refer to the exhibit.
A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?
- A. from interface fc1/10
- B. per packet, balanced between interfaces fc1/9 and fc1/10
- C. from interface fc1/9
- D. per flow, balanced between interfaces fc1/9 and fc1/10
Answer: D
NEW QUESTION 38
Which EtherType is used by the FCoE Initialization Protocol?
- A. 0*8913
- B. 0*8906
- C. 0*xfc0e
- D. 0*8914
Answer: D
NEW QUESTION 39
What does an unlicensed DCNM SAN fail to display?
- A. events and fault management
- B. real-time performance monitoring
- C. Fibre Channel, FCoE, and iSCSI topologies
- D. historical performance monitoring
Answer: B
NEW QUESTION 40
A storage network engineer must install and configure a new MDS switch in a data center network. Which two statements about available choices during the MDS switch initial setup are correct? (Choose two,)
- A. The engineer can choose what will be the administrator account
- B. The secure password standard is required.
- C. The engineer does not have the choice to enable or disable full roneset distribution
- D. The engineer can configure the default zone policy.
- E. The engineer can configure the default switch port trunK mode
Answer: B,D
NEW QUESTION 41
Refer to the exhibit.
An engineer is configuring Inter-VSAN routing for two Cisco MDS switches. The FSPF cost between the switches is 500, and the Cisco MDS core virtualizes an IVR NAT domain as shown. Which statement about the topology is correct?
- A. The MDS-Core simulates an IVR NAT, and the FSPF cost is 500.
- B. The MDS-Core simulates an IVR NAT, and increases the cost to 600.
- C. The MDS-Core simulates an IVR NAT, and increases the cost to 501.
- D. The MDS-Core simulates an IVR NAT, and decreases the cost to 400.
Answer: C
Explanation:
Section: Implementation
NEW QUESTION 42
Which result occurs if a device alias is renamed and then the original device alias name is used in an add command in the same session?
- A. The device alias is renamed and the add command is moved to the rejected list.
- B. The rename command is moved to the rejected list and the add command executes successfully.
- C. Both commands are moved to the rejected list.
- D. Both commands execute successfully.
Answer: D
NEW QUESTION 43
An engineer is configuring a SAN environment and attempts to activate a zoneset, but a lock is held by another user. Which argument does the engineer use to clear the locK from the zoning database configuration?
- A. abort
- B. force
- C. clear
- D. commit
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/6_2/configuration/guides/fabric/nx-os/nx_os_fabric/zone.html
NEW QUESTION 44
Which condition requires using a device alias rather than a Fibre Channel alias?
- A. All aliases being used are being configured in the same VSAN
- B. Aliases must be saved within a central database on the fabric
- C. The same alias must be used in zoning as well as DPVM
- D. The zone database must be distributed over the fabric
Answer: C
NEW QUESTION 45
Drag and drop the boot issues from the left onto the correct solutions on the right.
Answer:
Explanation:
NEW QUESTION 46
Which component is initially responsible for loading the kickstart image on Cisco MDS Switches?
- A. NX-OS
- B. BASH
- C. BIOS
- D. ROMMON
Answer: A
NEW QUESTION 47
Which EtherType is used by the FCoE Initialization Protocol?
- A. 0x8914
- B. 0xxfc0e
- C. 0x8906
- D. 0x8913
Answer: A
NEW QUESTION 48
Which statement accurately describes the result of disabling restrictions on oversubscription ratios on Cisco MDS 9000 Series Fibre Channel switching modules?
- A. The bandwidth allocation of the shared ports is equal to the lowest configured bandwidth.
- B. The bandwidth allocated to shared ports is proportionate to the configured speed of the ports.
- C. A port-group can contain a single port only.
- D. QoS can be configured.
Answer: B
NEW QUESTION 49
Which result occurs when a VSAN is deleted that contains non-trunking ports?
- A. The port configurations are cleared.
- B. The ports are moved to VSAN 4094.
- C. The ports are moved to VSAN 1.
- D. The ports are removed from the configuration.
Answer: B
NEW QUESTION 50
Refer to the exhibit.
Refer to the exhibit. Which configuration change improves the ability of the link to recover from frame loss?
- A. Increase the reset timeout.
- B. Increase the send buffer size to 15000 KB.
- C. Enable selective acknowledgment.
- D. Disable PMTU discovery.
Answer: D
NEW QUESTION 51
......
All 300-625 Dumps and Implementing Cisco Storage Area Networking Training Courses: https://pass4sure.actualpdf.com/300-625-real-questions.html
